Zinc oxide. Zinc oxide is a popular cross-linking agent for rubber and for various resins. It is essential in the formulation of solvent-borne polychloroprene adhesives. Furthermore, zinc oxide is a good UV stabilizer, has biocidal activity and has a relatively high refractive index (2.0) which makes it an efficient white pigment. Some typical properties are: density 5.6 g/cm³; particle size 0.036-3 μm; oil absorption 10–20 g/100 g; specific surface area 10–45 m²/g. Zinc oxide is produced by reaction of the metal in the vapour state with oxygen. Zinc oxide is nonporous and is quite pure. Thus, the high surface area of some grades is due to the small particle size of zinc oxide. Some grades, especially for use in the rubber industry, are surface modified by deposition of 0.2-0.4% of stearic acid, propionic acid, or light oil [47].

So what does this have to do with you?

3. Ceramics

By September, demand in the construction sector had significantly increased; however, resurgent cases of virus hindered the anticipated recovery in demand. However, due to a severe fall in market fundamentals in some end-use areas, its prices had significantly faded by quarter-end. Delays in a number of commercial projects, followed by a poor recovery in the downstream automotive market, were identified as primary causes of the protracted recovery curve.

After oral ingestion, the absorption of titanium dioxide particles is low, however they can accumulate in the body, Maged Younes, chair of the European Food Safety Authority's expert Panel on Food Additives and Flavourings, said in a May 2021 statement.

Lithopone

≤0.3

Nano-sized TiO₂ generally shows low or no acute toxicity in both invertebrates and vertebrates. However, exposure of Daphnia magna to 20 ppm TiO₂ for 8 consecutive days was found to cause 40 % mortality. Zhu et al. showed minimal toxicity to D. magna after 48 h exposure, while upon chronic exposure for 21 days, D. magna suffered severe growth retardation and mortality. A significant amount of nano-sized TiO₂ was found also accumulated in the body of the animals. Similar findings with coated nano-sized TiO₂ (T-Lite™ SF, T-Lite™ SF-S and T-Lite™ MAX; BASF SE) were reported by Wiench et al. Biochemical measurements showed that exposure to TiO₂ NPs induces significant concentration-dependent antioxidant enzyme activities in D. magna. Lee et al. showed that 7 and 20 nm-sized TiO₂ induced no genotoxic effect in D. magna and in the larva of the aquatic midge Chironomus riparius.

Alterations in gut microbiota

2: Clarification mechanism of coagulant

Chemical coagulation is a process in which chemical agents (coagulants) are added to water treatment to make colloidal dispersion system destabilize and agglomerate. In the coagulation process, small suspended particles and colloidal impurities are aggregated into larger solid particles to separate particulate impurities from water, which is called coagulation clarification.

After adding coagulant into water, colloidal particles and other small particles can be polymerized into larger flocs through the comprehensive action of mixing, coagulation and flocculation. The whole process of coagulation and flocculation is called coagulation.

(1) Destabilization and condensation of colloids

Adding electrolyte to water can compress the electric double layer and destabilize the colloid. The main mechanism is that the electric double layer of colloidal particles in water is compressed or neutralized by adding aluminum salt or iron salt coagulant. The coagulant and raw water are mixed rapidly and evenly, and a series of chemical reactions are produced to destabilize. This process takes a short time, generally about 1 min. Some cationic polymers can also play a role in the destabilization and condensation of colloids in water. These polymers have a long chain structure and positive charge in water. Their destabilization and condensation of colloids in water is due to the interaction of van der Waals force adsorption and electrostatic attraction.

(2) Flocculation and formation of floc (alum)

The particle size of the initial flocculate formed by colloid destabilization and coagulation in water is generally more than 1 m. at this time, Brownian motion can no longer push them to collide and form larger particles. In order to make the initial flocs collide with each other to form large flocs, it is necessary to input additional energy into the water to produce a velocity gradient. Sometimes it is necessary to add organic polymer flocculant into water, and the adsorption bridging effect of long chain molecules of flocculant is used to improve the probability of collision and adhesion. Flocculation efficiency usually increases with the increase of flocculate concentration and flocculation time.

Compared with polyaluminum chloride, polyaluminum chloride has the advantages of high density, fast settling speed and wide pH adaptability; the coagulation effect is less affected by temperature than that of polyaluminum sulfate; however, when adding ferric salt, it should be noted that when the equipment is not in normal operation, the iron ions will make the effluent color, and may pollute the subsequent desalination equipment.